HVTS-HP series

MOBILE HIGH-POWER HIGH-VOLTAGE TEST SYSTEMS

The HVTS-HP series systems are designed for high-voltage withstand testing of various dielectrics with higher levels of DC or AC voltage (UDC ≤ 140 kV; UAC ≤ 100 kVRMS, f = 50 Hz).

The systems could be used in the field or for laboratory testing.
Hvts hp  top  454x454

VERSATILITY

The system features both DC (rectified) and AC output voltage modes, which allows to use a single HVTS-HP system for testing such electrical equipment as cables, current transformers, switchgear, sectionalizing joints, etc. according to various standards and regulation.

Hvts hp ac dc  1200x831 2
Hvts hp pered  1200x831

HIGH POWER

The power output of HVTS-HP series systems ("HP" means "High Power") is several times higher than that of its analogues.

The output current and voltage at the test object can reach 175 mARMS/100 kVRMS and 80 mA/140 kV in AC and DC modes respectively.

DIGITAL CONTROL

HVTS-HP systems feature a digital graphic display indicating all the test settings and operating parameters.

Digital user interface enables HVTS-HP to feature a multi-language menus, as well as viewing test reports, saving test pre-sets, etc.

Ruchnoj hp  1200x831
Hvts hp panel 01 1200x831

MANUAL AND AUTOMATIC CONTROL MODES

The system allows to carry out tests in both fully automatic and manual control modes.

In the manual mode, the output voltage level and ramp up rate are controlled by the operator via a rotary encoder.

In the automatic mode, the test voltage is automatically increased at pre-defined ramp up rate and is held on the required level before being reduced to zero upon completion of the test cycle.

Switching between control modes is done by simple push of a button.

MOBILITY

Light weight, compact size and trolley-form design of both units of the system enable rapid deployment, quick reconnection and operational comfort during the field testing.

Mobilnost 1200x831
Elektrods 1200x831

SAFETY

The system consists of two separate modules: the control unit and the high voltage unit.

The test process is controlled from the control unit while an object under test is connected to the high-voltage unit.

Such two-module design allows an operator to remain at a safe distance away from the high-voltage circuit and the object under test.

* Pictures used herein are for illustration purposes only. Products' specifications are subject to change without notice. *


Technical Specifications

 

HVTS-HP

100/100-7.5 (17.5)

HVTS-HP

140/100-7.5 (17.5)

 

DC testing parameters

Voltage

Output level

up to 100 kV

up to 140 kV

Measurement error

± [3 % + 2 dgt]*

Current

Output level

up to
40 (80) mA
**

up to
30 (60) mA

Measurement error

± [3 % + 2 dgt]

AC testing parameters

Voltage

Output level

up to 100 kVRMS

Measurement error

± [3 % + 2 dgt]

Current

Output level

up to 75 (175) mARMS

Measurement error

± [3 % + 2 dgt]

System parameters

Test modes

   Manual

   Auto

Load capacitance in AC mode

@ rated output voltage

up to 2.4 (5.4) nF

Voltage ramp up rate

0.5 … 4.0 kV/s, step 0.5 kV/s

Internal memory

32 test reports

Test timer setting range, user-defined

0:10 … 59:59 min

Interface

Monochrome graphical display

128×64 px

Interface languages

  •      RU, EN
  •      TR, PL, FR, etc. (option)

Safety

  • Protection
  •      Over-voltage tripping
  •      Over-current tripping
  •      Thermal overload warning
  •      Low pressure warning

Power supply and consumption

Supply voltage

230 V ± 10 %, AC, single phase

Supply frequency

50 Hz

Power consumption

up to 9 (19) kVA

Current consumption

40 (82) A***

Physical

CU dimensions, H×W×D

1063×735×561 mm

CU weight

82 (127) kg

HVU dimensions, H×W×D

1012×639×750 mm

HVU weight

125 kg



* The measurement error of a digital tester is specified by the expression: ± [xx% rdg + xx dgt], where the first portion identifies a percentage error relative to the reading, which means it is proportional to the input. The second portion is an error in digits that indicates the counts on the last significant digit of the digital display (the lowest digit in a number, located at the far right of a string). The error in digits is constant regardless of the input and is typically used to represent an error factor of a digital tester.

** The parameters in parentheses apply to the 17.5 versions of the System.

*** Inrush current may be greater. If used with an automatic circuit breaker in the mains supply, a minimum of 63 A (100 A for 17.5 version) breakers are recommended.

 
 

Related products

HVTS-70/50 – Portable high-voltage test system
VLF-60 – Portable high-voltage VLF test system
UIG series – Resonant testers
Cables & wires – High-voltage cables
OLT series – Automatic insulating oil dielectric strength testers
We use cookies to allow us to better understand how the site is used. By continuing to use this site, you consent to this policy. Click to learn more. Learn more